Download DesignJet C Service from folder Printers DesignJet. DesignJet C Service Manual pdf. From folder: Printers HP DesignJet. View and Download HP C user manual online. DRAFTING PLOTTERS SERVICE MANUAL. C Plotter pdf manual download. Also for: Designjet c . Service Manual and more parts for CA DesignJet c printer.

Author: Zulushicage Tasida
Country: Vietnam
Language: English (Spanish)
Genre: Photos
Published (Last): 17 March 2011
Pages: 254
PDF File Size: 7.12 Mb
ePub File Size: 16.61 Mb
ISBN: 637-2-32378-291-8
Downloads: 68475
Price: Free* [*Free Regsitration Required]
Uploader: Akigar

In addition, worded error messages; system error codes; and internal service menu tests are segvice. This feature can be used to ensure proper data reception. Remove the bail assembly. Automatic media edge sensing Access Pens brings the pen 605c out to the plotting area for pen access. Disconnect the window sensor cable connector from the front panel PCA.

Also See for C Specification sheet – 1 page Frequently asked questions manual – 37 pages. Dry time determines how long the plotter waits before cutting the plot.

Using a TORX T screwdriver, loosen the upper of the two screws that attach the the starguard assembly to the left and right sideplates until servife ends of the screws are flush with the inner surfaces of the sideplates.

Product has been exchanged: The pen carriage moves out from the pen service sta- tion at the left of the plotter and stops in front of the slot in the bail. Remove the front trim pieces.

Disconnect the carriage motor cable connector labeled Deisgnjet from the interconnect PCA. Using a TORX T screwdriver, remove the two front screws that connect each endcover and front sideplate trim to the plotter. Calibrate done Accuracy calibration is complete.


Perform the bail calibration whenever the: Perform the media sensor calibration whenever the: Table of Contents Add to my manuals Add. Asia Pacific and Oceania.

Accessing Pens Figure shows you how to visually check the ink level in a cartridge. Using a TORX T servics, remove the three screws that secure the rollfeed module assembly to the sideplate.

Mispositioned Roll is mispositioned. Load the leading edge of the sheet making sure to push the sheet in straight not skewed while aligning the right edge of the sheet with the perforated line on the entry platen. See your browser’s documentation for specific instructions.

The pen carriage will move into the platen area to allow easy access to the pens. 6650c 38 Front panel controls and LEDs are described below.

The front panel contains a 2-row by character vacuum fluorescent display. Quality color output is only supported when using HP special inkjet paper. Also provided is a listing of when each procedure is required. Please use the 650v number and serial numbers of the new product to validate warranty status. In roll media opera- tions, the user can choose between continuous deeignjet or cutting plots off the roll automati- cally as they are completed. Comments to this Manuals Your Name.

Remove the electronics enclosure cover. By completing and submitting this form you consent to the use of your data in accordance with HP’s Privacy statement. This process can take several minutes depending on the number of warranties being checked.

HP DesignJet Printer series User Guides | HP® Customer Support

To install, place the pinch arm assembly spring into its bushing. To remove the trailing cable, perform the following procedure: If an MIO card is not already installed, use a small flat blade or Torx T10 screwdriver to remove the two screws that attach the cover plate to the top back of the plotter.


Figurelocated at the end of this chapter, provides a diagram of the menu tree showing the various menus and submenus of the DesignJet C plotters. The devices may be connected in a dexignjet or linear bus network.

HP 650C User Manual

Using a TORX T screwdriver, remove the screws that attach the front trim pieces to the left and fesignjet sideplates. Remove the window assembly. Page Notes Product History DesignJet C documentation listed in Chapter 1 of this manual.

Check the drop sense cable connections. Move the pen carriage to the center of its travel.

Download DesignJet C Service – Printers DesignJet designjet c service manual

Page of Go. Press the pinch arm assembly back and rotate it to the vertical eesignjet. It sends configuration information to the car- riage processor via its serial port.

Parts lists with associated illustrated parts break- down drawings are provided. Feed the rubber tubes through the slot in the bottom of the service station housing while lowering the sled into position. Learn more about HP’s privacy policy. Also include the plotter model 650x serial number on the parts order.