EEPROM 95160 PDF

STMicroelectronics MW Series EEPROM are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for STMicroelectronics . Errors and solutions here for eeprom read/write with Carprog programmer: Error 1: “ID not found” when read eeprom EEPROM, Serial SPI, 16 Kbit, 2K x 8bit, 10 MHz, SOIC, 8 Pins The M WMN6P is a 16Kbit (2K x 8bit) serial SPI bus EEPROM (Electrically Erasable.

Author: Yozshumi Gardasar
Country: Cuba
Language: English (Spanish)
Genre: Software
Published (Last): 19 July 2005
Pages: 451
PDF File Size: 18.35 Mb
ePub File Size: 13.67 Mb
ISBN: 868-7-13688-717-8
Downloads: 57731
Price: Free* [*Free Regsitration Required]
Uploader: Mugrel

Hi, i have connected the tool to the chip and adapter to the programmer. It is SOIC8 mil chip. Reply 9 ZLM Posts. If the chip is not designed for programming in eeorom, then you need to try to find some connection.

That is depending on your circuit design. You need to find a way to test the data. Reply 11 benaknoun Spain Posts. Reply 8 benaknoun Spain Posts. What is exact part number? Also, when i click on ID, it says “function not supported on this device” Image Insert: The only way to test data is: Reply 13 benaknoun Spain Posts.

Chip is blank does this mean this chip is empty??? Reply 16 benaknoun Spain Posts. But the fast way is to remove it from board and program it on the programmer ZIF spcket directly.

  LAGUNA ALALAY COCHABAMBA PDF

Carprog 9.31 reads/writes eeprom 95160 with A4/A6 adapter

Device blank check failed at address: Hi, i have received the tools i bought eeprpm mcumall canada, there are numbers on the adapters, how do i know which pin is the right matching one with the chip?

All other pins are pin to pin connect to programmer socket. I think it should be SOIC8 mil chip. Reply 17 ZLM Posts. What is your another adapter part number?

MCUmall EPROM BIOS Chip Burner Forum – 8pin

It should be able to open it by same software. Reply 5 ZLM Posts. Reply 19 ZLM Posts. You can save data as. Reply eepdom benaknoun Spain Posts. So, if you can not read anything out, make sure your pins have good contacting.

Once the chip is blank, then you can load your data file and click on Write button to wrtie the data into chip. Then the ADP should be used. Eerom “Device blank check failed ” means the chip is not a blank chip, there are some data in the chip.

Reply 18 benaknoun Spain Posts. Reply 4 benaknoun Spain Posts. Reply 7 ZLM Posts. To be honest though, the other adapter i bought, not sure what its for??

  BRUNO BOSTEELS PDF

Hi, it seems i’m doing something right then! Also, another question please about the same chip: Reply 14 benaknoun Spain Posts. What is your chip eperom board?

Reply 2 benaknoun Spain Posts. Hi, thanks for your reply, here are the numbers on the weprom Which part number you selected in software? Use ToolA instead, because your chip pins already damaged.

Reply 3 ZLM Posts. Reply 15 ZLM Posts. Try to power up the board and do not connect pin 8 Vcc pin. Reply 1 ZLM Posts.

Carprog reads/writes eeprom with A4/A6 adapter | OBDIIcom Official Blog

That is safe and fastest way. Reply 12 ZLM Posts. Hi, ok forget this chip, its damaged Reply 10 benaknoun Spain Posts. If it is “”, then it has no ID on this chip. I believe they will do the job. Most of used on-board chips should have something. The wire can be any wires, as long as you can solder it.

When you uploading the image, only use letter and number as file name.